How do you actually feel when it comes to A Step-by-Step Guide to Installing a Bathtub?
Setting up a tub isn't specifically brain surgery, yet it does call for strong plumbing, woodworking, and sometimes, tiling skills. Replacing an old bathtub with a new one is additionally a moderately tough project. If the old tub is readily accessible, the project can move speedily; if you need to open up a wall surface to get rid of the old bathtub and also position the new bathtub, the job is a lot harder. In either instance, the task is within a residence handyman's abilities, although you will need a helper to leave the old tub as well as set in the new one. Make sure you have certified on your own for the job and fit attempting it. Instead of working with a service provider to take control of a halfway-completed task, it is much better to think about utilizing one before you begin. Opportunities are you might require an expert plumber to make tube connections.
This article will certainly aid you mount a new bathtub in your bathroom if you have actually currently gotten a new tub and also do not need to transform the plan of your previous water system pipes.
Your devices and also material checklist need to consist of the following:
Removing Old Touches
If you need to replace old faucets with new ones as a part of your installment, after that the first thing you ought to do is disconnect the water. After doing so, switch on the taps to drain pipes any type of water remaining in the system. The procedure of eliminating the existing taps can be fairly troublesome as a result of the limited access that is usually the situation.
Use a container wrench (crowsfoot spanner) or a tap device to reverse the nut that attaches the supply pipes to the faucets. Have a fabric ready for the staying water that will originate from the pipes. As soon as the supply pipes have actually been eliminated, make use of the exact same device to loosen the nut that holds the faucets onto the bath/basin. You will certainly require to stop the solitary taps from transforming during this process. As soon as the taps have actually been eliminated, the holes in the bath/basin will certainly have to be cleansed of any type of old securing compound.
Prior to moving on to fit the brand-new taps, contrast the pipeline connections on the old faucets to the new faucets. If the old taps are longer than the new faucets, then a shank adapter is required for the brand-new taps to fit.
Fitting New Touches
If the tails of the new faucets are plastic, after that you will require a plastic connector to avoid damages to the thread. One end of the adapter fits on the plastic tail of the tap as well as the various other end offers a link to the existent supply pipes.
If you require to fit a monobloc, then you will need lowering couplers, which connects the 10mm pipeline of the monobloc to the typical 15mm supply pipe.
Next off, place the tap in the installing opening in the bath/basin ensuring that the washers remain in place between the faucet and also the sink. Secure the tap in position with the supplier offered backnut. When the faucet is securely in position, the supply pipelines can be connected to the tails of the taps. The faucets can either be attached by using corrugated copper piping or with normal faucet adapters. The previous type ought to be linked to the faucet finishes first, tightening only by hand. The supply pipelines can later on be attached to the other end. Tighten both ends with a spanner after both ends have been linked.
Setting up the Tub
Making use of both wooden boards under its feet, place the tub in the needed setting. The wood boards are handy in evenly spreading the weight of the bathtub over the area of the boards rather than concentrating all the weight onto 4 tiny factors.
The following objective is to ensure that the bathtub is leveled all round. This can be achieved by examining the spirit level and adjusting the feet on the bathtub until the spirit level reads level.
To install taps, fit the bottom of the furthest flexible tap port to the suitable supply pipe by making a compression join; then do the same for the other tap.
Switch on the supply of water and examine all joints and also brand-new pipework for leakages as well as tighten them if needed. Fill up the tub and likewise check the overflow outlet and the normal outlet for leakages.
Ultimately, deal with the bathroom paneling as explained in the producer's instruction manual. Tiling and sealing around the bathtub needs to wait till the bathtub has actually been made use of at the very least when as this will settle it right into its last setting.
Getting ready for the Installation
Firstly, the sustaining structure provided with the bath should be fitted (if called for) according to the supplier's directions. Next, fit the taps or mixer to the bath tub. When suitable the tap block, it is necessary to make certain that if the tap comes with a plastic washing machine, it is fitted in between the bath and also the faucets. On a plastic bath, it is also reasonable to fit a supporting plate under the taps device to avoid strain on the bath tub.
Fit the versatile tap adapters to the bottom of both taps making use of 2 nuts as well as olives (in some cases provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and afterwards pass the outlet via the hole in the bathroom. Use the nut provided by the producer to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the adaptable overflow pipeline to the overflow outlet. Afterwards, screw the pipe to the overflow face which must be fitted inside the bath. See to it you utilize every one of the supplied washing machines.
Connect the catch to the bottom of the waste outlet on the bath tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the catch to the outlet. Attach the bottom of the overflow tube in a comparable manner.The bath must now be ready to be suited its final placement.
Tiling Around the Tub
In the location where the bath fulfills the tile, it is needed to secure the joins with a silicone rubber caulking. This is very important as the installation can move sufficient to crack a stiff seal, causing the water to permeate the wall surface between the bathroom and also the tiling, resulting in difficulties with dampness as well as feasible leaks to the ceiling listed below.
You can choose from a range of coloured sealers to blend in your fixtures and also fittings. They are marketed in tubes and cartridges, as well as can sealing spaces approximately a width of 3mm (1/8 inch). If you have a larger space to load, you can fill it with twists of drenched paper or soft rope. Remember to constantly load the bathtub with water before sealing, to permit the movement experienced when the tub is in usage. The sealer can crack fairly early if you do not take into consideration this activity before sealing.
Additionally, ceramic coving or quadrant floor tiles can be used to edge the bath or shower tray. Plastic strips of coving, which are easy to use as well as reduce to dimension, are also easily offered on the marketplace. It is suggested to fit the tiles using water-resistant or water resistant sticky and also cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I found that blog posting about A Step-by-Step Guide to Installing a Bathtub when doing a lookup on the search engines. Sharing is nice. You just don't know, you might be helping someone out. Thanks for taking the time to read it.
Call Us Today